Found while testing crates/io/src/svg.rs:50-60 (export_list: viewBox, stroke-width, circle r and coordinates all formatted with {:.6})
Co-authored-by: Claude Haiku 5.5 <noreply@anthropic.com>
AutoCAD writes $ANGBASE in degrees (a drawing whose angles run clockwise from
north has 90.0); CADCraft read and wrote it as radians, so such a drawing's
angle base came in as 90 radians (about 116.6 degrees), turning typed angles,
polar tracking and angles shown in Properties. The reader now converts to
radians (the variable's unit), the writer back, and the DWG reader's hand-off
of the value in DXF form gives degrees.
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Paper-space units followed the drawing's MEASUREMENT only, so a layout
whose page setup is in millimetres (plot paper units 1), common in
drawings from AutoCAD with MEASUREMENT 0, was taken as inches: its PDF
drew everything 25.4 times too large, off the page.
PageSetup gains `paper_mm`, read from LAYOUT group 72 = 1; 72 = 0 still
leaves the units to MEASUREMENT, since earlier CADCraft versions wrote 0
for every layout. The layout's sheet, its PDF/raster plots, PREVIEW and
the pens of what its viewports show use the layout's units, and the
writer stores 72 = 1 for layouts in millimetres (it wrote 0 always).
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
acadrust writes every paper-space entity with entity mode 1 ("paper
space"), including those of *Paper_Space0, *Paper_Space1… and relies on
each block's entity list; AutoCAD reads mode 1 as the *Paper_Space
block's, so what was drawn on a second layout (and its viewports, in
drawings from AutoCAD with several layouts) landed on the first one, and
the second stayed empty. The DWG bridge now writes those entities owned
by their block (entity mode 0 with the owner handle), as the public DWG
specification describes; the first layout's entities stay mode 1.
The io tests read CADCraft's DWG back with acadrust (a dev-dependency,
the same version as cadcraft-dwg's) to check the modes as written.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* AutoCAD interop: justified text, DIMPOST, current dimension style, *D block colours
What AutoCAD takes from CADCraft's DWG/DXF as it is:
- Justified TEXT/ATTRIB/ATTDEF (#1050): group 10 is now where the
baseline starts, from the alignment point and the text's width, not
the alignment point itself; AutoCAD drew centred and right-aligned
text from DWG starting at its alignment point. A stored point close to
CADCraft's own (AutoCAD's, exact for its fonts) is kept.
- DIMPOST (#1053) is written even when empty: the DWG bridge defaulted a
missing one to "<>", and AutoCAD then dropped the "R" of radius
dimensions when it regenerated them.
- The current dimension style (#1051): the DXF header now carries its
DIM* variables (AutoCAD draws new and updated dimensions from them);
the DWG bridge points $DIMSTYLE at the style by name (its handle was
renumbered, so the writer fell back to Standard), and reading a DWG
gives the current dimension and text styles their names back.
- *D blocks (#1052): lines, arrows, extension lines and text take the
style's DIMCLRD/DIMCLRE/DIMCLRT instead of ByBlock.
#1054 (group 42 of a rotated linear dimension) was already fixed on
main by #855; acad_interop.rs keeps it covered.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Test: angular dimensions store their angle in radians (group 42)
Three-point (60°, 174°) and two-line (120°) angular dimensions, read back
from the DWG as DXF. Already right on main since #855; this guards it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Justified text made here: Left Middle and Left Bottom write their baseline start too
text_insert kept a stored insertion point that was within 0.1 x an
estimated width + 0.5 x height of CADCraft's baseline start, taking it for
AutoCAD's own. The width was estimated from the alignment point's offset,
which for Left Middle is only h/2 (vertical), so a text made here, whose
stored point is the alignment point, passed and kept it: AutoCAD drew it
half a height high (Left Bottom: a third). Reported with a test by
@lee-cyrille-maskell.
A stored point equal to the alignment point is now always stale. Otherwise
the offset is split along and across the baseline: along it the same slack
as before (a tenth of the text's width plus half its height, as fonts and
their substitutes differ most in width), across it a fifth of the height.
Multiline attribute values keep the distance-only check, since their lines
are placed by the embedded MTEXT.
On 12 drawings made in AutoCAD (1,055 justified texts) the insertion points
written are the same as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Multiline attributes: read, draw and save their text
A multiline attribute (DXF attribute type 2, or 4 for a definition) has its
text as embedded MTEXT after its own groups (`101 Embedded Object`); its own
group 1 is empty. CADCraft read only the own groups, so the attribute drew
nothing, and a save wrote it back empty: its text was lost.
- `Attrib::multiline` keeps the multiline text; `text.value` holds its plain
text, which ATTEDIT and the other value editors change; an edited value
replaces the contents (`Attrib::multiline_text`).
- DXF read: ATTRIB and ATTDEF split at the marker; the MTEXT parsing is
shared with MTEXT entities (`mtext_from`).
- Drawn as multiline text; ZOOM Extents counts it.
- DXF write (2007 and later; earlier versions get one line): attribute type,
alignment point and the embedded MTEXT, only what differs from unrotated
text, as AutoCAD writes it.
- INSERT and ATTSYNC give references the definition's multiline text placed
with them; MOVE/ROTATE/SCALE, Properties rotation and scale, annotative
scaling and FLATTEN carry it.
- Tests: synthetic multiline ATTDEF and ATTRIB (read, drawn, saved, edited,
pre-2007 save, damaged embedded groups); engine INSERT, MOVE, ATTEDIT and
ATTSYNC.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Multiline attributes: read MTEXT direction from its own groups (#667, as #834 does)
#834 moves these lines' fix into the MTEXT reader; the same fix in the shared
mtext_from keeps the two compatible.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Attributes keep Verify, Preset and Lock position
ATTDEF/ATTRIB flags 4 (verify) and 8 (preset) and Lock position (group 280
after the tag, DXF 2007 and later) were dropped on save. Without Lock
position AutoCAD lets an attribute be dragged out of its reference, and its
dynamic block actions no longer carry it. A reference's attributes take Lock
position from their definitions, as AutoCAD saves them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Multiline attributes: read, draw and save their text
A multiline attribute (DXF attribute type 2, or 4 for a definition) has its
text as embedded MTEXT after its own groups (`101 Embedded Object`); its own
group 1 is empty. CADCraft read only the own groups, so the attribute drew
nothing, and a save wrote it back empty: its text was lost.
- `Attrib::multiline` keeps the multiline text; `text.value` holds its plain
text, which ATTEDIT and the other value editors change; an edited value
replaces the contents (`Attrib::multiline_text`).
- DXF read: ATTRIB and ATTDEF split at the marker; the MTEXT parsing is
shared with MTEXT entities (`mtext_from`).
- Drawn as multiline text; ZOOM Extents counts it.
- DXF write (2007 and later; earlier versions get one line): attribute type,
alignment point and the embedded MTEXT, only what differs from unrotated
text, as AutoCAD writes it.
- INSERT and ATTSYNC give references the definition's multiline text placed
with them; MOVE/ROTATE/SCALE, Properties rotation and scale, annotative
scaling and FLATTEN carry it.
- Tests: synthetic multiline ATTDEF and ATTRIB (read, drawn, saved, edited,
pre-2007 save, damaged embedded groups); engine INSERT, MOVE, ATTEDIT and
ATTSYNC.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Multiline attributes: read MTEXT direction from its own groups (#667, as #834 does)
#834 moves these lines' fix into the MTEXT reader; the same fix in the shared
mtext_from keeps the two compatible.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Dynamic blocks: read parameters and actions from AutoCAD files
A dynamic block's evaluation graph (kept as foreign data since #528) is read
into a typed model, `cadcraft_doc::dynblock`, without changing the kept
data: parameters (linear with value sets, point, visibility states,
lookup, base point; polar, XY, rotation, alignment and flip by geometry)
and actions (stretch with its frame and moved vertices, lookup tables;
move, scale, rotate, flip, array, polar stretch by kind), each with its
graph id and the parameters it follows.
- `blocks.dynamic {name}` returns the model as JSON (handles as hex);
`blocks.list` marks dynamic blocks.
- Counts and values come from the file: capped by the groups present,
non-finite numbers and missing members skipped.
- Tests: a synthetic DOOR block (visibility, linear list, stretch, lookup),
its survival through a save, damaged data, and the engine commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: their values and custom properties
A dynamic block reference's extension dictionary says which dynamic block it
shows (AcDbBlockRepresentation ▸ AcDbRepData) and the values it was given
(AppDataCache ▸ ACAD_ENHANCEDBLOCKDATA, one XRECORD per parameter graph id).
`dynblock::reference` reads them; a reference to the dynamic block itself
has the block's values.
- `dynblock::custom_properties`: the Properties palette's Custom section, in
parameter order, only parameters shown in Properties: visibility state,
lookup value worked out from the lookup tables (their "no match" name, e.g.
Custom, when the inputs match no row), distances and point positions in
drawing units (block units × the reference's scale), with the choices of
each (states, lookup values, a distance's list).
- Properties: a dynamic block reference shows its dynamic block's name
instead of its anonymous block's, and a read-only Custom section.
- `blocks.reference {handle}` returns the definition, values and properties.
- Tests: synthetic references (own values, an anonymous block scaled 2, a
width no lookup row has), survival through a save, the engine command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: change the visibility state
Choosing a visibility state (or a lookup value whose tables set only
visibility states) in Properties ▸ Custom, or `blocks.reference.set
{handle, name, value}`, changes a dynamic block reference as AutoCAD does:
- The reference gets a new anonymous block: its current one with the
state's objects shown and the parameter's other objects hidden (matched
to the dynamic block's objects by their AcDbBlockRepETag element tags).
The old anonymous block goes when nothing else uses it.
- AutoCAD's link data is written: the new block's record carries
AcDbBlockRepBTag (the dynamic block's record), copied objects keep their
element tags, and the reference's AcDbBlockRepresentation data records the
value (an existing value record is updated; a new one copies another
reference's record for the same parameter when there is one).
- An attribute whose definition the state hides is written hidden (60).
- Changes CADCraft can't make yet (distances, positions, lookups that set
them) are refused with a message and change nothing; Properties shows
only what can change as a dropdown (`CustomProperty::editable`).
- Tests: the synthetic DOOR references (own values and an anonymous block),
survival through a save, refusals, and the engine command with undo.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: distances, positions, stretch and move actions, lookup chaining
Linear distances (snapped to their value sets) and point positions can be
changed; the stretch and move actions that follow them run (listed vertices
or whole objects, multiplier and angle offset), parameters in an action's
selection are carried along, associative hatches refill from their
stretched outlines and the reference's attributes move with their
definitions. Lookup tables run both ways (a changed input gives its table's
lookup value, which sets the other tables' inputs). Connections are read in
either group order. Checked against AutoCAD's own references (*U10, *U12).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: record changes in the history as AutoCAD does; full value data for new references
A changed reference's ACAD_ENHANCEDBLOCKHISTORY says what was done to it: a
visibility state or lookup value by property name, a distance or position as
the drag of its grips (GRIPLOC, how far each grip is from where the dynamic
block has it). A reference that had no data gets a record for everything
other references of the same dynamic block have, with its own values.
Templates come only from references of the same dynamic block; anonymous
copies have no units; boundary reactors follow the copies.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block history: record only the grips a change moves
AutoCAD's history holds the user's own drags; a grip that only moved with
another parameter (a stretch carrying it) gets no entry.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block history: a distance by name, as typed in Properties
AutoCAD records a distance typed in Properties as the parameter's name and
value in block units (1071 id, 300 Distance2, 40 40.0), replacing drags of
its grips; positions stay grip drags.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* DWG: dynamic block lookup parameters keep their name and lookup action
AutoCAD writes a lookup parameter's subclass marker as
AcDbBlockLookUpParameter; the DWG bridge reads AcDbBlockLookupParameter and
matches it exactly, so the parameter's name (303) and lookup action (94)
were lost in DWG files and AutoCAD's lookups stopped working (a visibility
change no longer resized the block). The bridge DXF now uses its spelling.
Found by driving AutoCAD on CADCraft's output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic blocks: carried parameter points are in a stretch frame where the block has them
AutoCAD evaluates actions from the dynamic block itself, so a parameter point
another action has moved out of a stretch frame still follows it. Testing the
current position instead changed a stretched label's width when its
visibility changed (Distance2 183.75 became 184.45; AutoCAD keeps 183.75).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block grips: show and drag a dynamic reference's grips as AutoCAD does
A selected dynamic block reference shows its grips: an arrow at each end of a
distance, a square at a position, a down-pointing triangle for a visibility
or lookup list, only those its visibility state lists. Dragging an arrow
changes the distance along the parameter (snapped to its values; a typed
number sets it), a square moves the position, a list grip offers its
choices; actions and lookups follow, with a live preview.
doc: dynblock::grips, drag_grip; grip objects by graph id.
engine: blocks.reference.grips, blocks.reference.grip, Session::start_dyn_grip.
ui: canvas dynamic grips (GRIPDYNCOLOR-like token), list popup.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Tests: read the shared DOOR fixture with LF line ends whatever the checkout gives
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic blocks: carried parameter points are in a stretch frame where the block has them
AutoCAD evaluates actions from the dynamic block itself, so a parameter point
another action has moved out of a stretch frame still follows it. Testing the
current position instead changed a stretched label's width when its
visibility changed (Distance2 183.75 became 184.45; AutoCAD keeps 183.75).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic grips: Ukrainian labels for the new commands; copy the hot grip instead of cloning
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Dynamic blocks: read parameters and actions from AutoCAD files
A dynamic block's evaluation graph (kept as foreign data since #528) is read
into a typed model, `cadcraft_doc::dynblock`, without changing the kept
data: parameters (linear with value sets, point, visibility states,
lookup, base point; polar, XY, rotation, alignment and flip by geometry)
and actions (stretch with its frame and moved vertices, lookup tables;
move, scale, rotate, flip, array, polar stretch by kind), each with its
graph id and the parameters it follows.
- `blocks.dynamic {name}` returns the model as JSON (handles as hex);
`blocks.list` marks dynamic blocks.
- Counts and values come from the file: capped by the groups present,
non-finite numbers and missing members skipped.
- Tests: a synthetic DOOR block (visibility, linear list, stretch, lookup),
its survival through a save, damaged data, and the engine commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: their values and custom properties
A dynamic block reference's extension dictionary says which dynamic block it
shows (AcDbBlockRepresentation ▸ AcDbRepData) and the values it was given
(AppDataCache ▸ ACAD_ENHANCEDBLOCKDATA, one XRECORD per parameter graph id).
`dynblock::reference` reads them; a reference to the dynamic block itself
has the block's values.
- `dynblock::custom_properties`: the Properties palette's Custom section, in
parameter order, only parameters shown in Properties: visibility state,
lookup value worked out from the lookup tables (their "no match" name, e.g.
Custom, when the inputs match no row), distances and point positions in
drawing units (block units × the reference's scale), with the choices of
each (states, lookup values, a distance's list).
- Properties: a dynamic block reference shows its dynamic block's name
instead of its anonymous block's, and a read-only Custom section.
- `blocks.reference {handle}` returns the definition, values and properties.
- Tests: synthetic references (own values, an anonymous block scaled 2, a
width no lookup row has), survival through a save, the engine command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: change the visibility state
Choosing a visibility state (or a lookup value whose tables set only
visibility states) in Properties ▸ Custom, or `blocks.reference.set
{handle, name, value}`, changes a dynamic block reference as AutoCAD does:
- The reference gets a new anonymous block: its current one with the
state's objects shown and the parameter's other objects hidden (matched
to the dynamic block's objects by their AcDbBlockRepETag element tags).
The old anonymous block goes when nothing else uses it.
- AutoCAD's link data is written: the new block's record carries
AcDbBlockRepBTag (the dynamic block's record), copied objects keep their
element tags, and the reference's AcDbBlockRepresentation data records the
value (an existing value record is updated; a new one copies another
reference's record for the same parameter when there is one).
- An attribute whose definition the state hides is written hidden (60).
- Changes CADCraft can't make yet (distances, positions, lookups that set
them) are refused with a message and change nothing; Properties shows
only what can change as a dropdown (`CustomProperty::editable`).
- Tests: the synthetic DOOR references (own values and an anonymous block),
survival through a save, refusals, and the engine command with undo.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: distances, positions, stretch and move actions, lookup chaining
Linear distances (snapped to their value sets) and point positions can be
changed; the stretch and move actions that follow them run (listed vertices
or whole objects, multiplier and angle offset), parameters in an action's
selection are carried along, associative hatches refill from their
stretched outlines and the reference's attributes move with their
definitions. Lookup tables run both ways (a changed input gives its table's
lookup value, which sets the other tables' inputs). Connections are read in
either group order. Checked against AutoCAD's own references (*U10, *U12).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: record changes in the history as AutoCAD does; full value data for new references
A changed reference's ACAD_ENHANCEDBLOCKHISTORY says what was done to it: a
visibility state or lookup value by property name, a distance or position as
the drag of its grips (GRIPLOC, how far each grip is from where the dynamic
block has it). A reference that had no data gets a record for everything
other references of the same dynamic block have, with its own values.
Templates come only from references of the same dynamic block; anonymous
copies have no units; boundary reactors follow the copies.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block history: record only the grips a change moves
AutoCAD's history holds the user's own drags; a grip that only moved with
another parameter (a stretch carrying it) gets no entry.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block history: a distance by name, as typed in Properties
AutoCAD records a distance typed in Properties as the parameter's name and
value in block units (1071 id, 300 Distance2, 40 40.0), replacing drags of
its grips; positions stay grip drags.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* DWG: dynamic block lookup parameters keep their name and lookup action
AutoCAD writes a lookup parameter's subclass marker as
AcDbBlockLookUpParameter; the DWG bridge reads AcDbBlockLookupParameter and
matches it exactly, so the parameter's name (303) and lookup action (94)
were lost in DWG files and AutoCAD's lookups stopped working (a visibility
change no longer resized the block). The bridge DXF now uses its spelling.
Found by driving AutoCAD on CADCraft's output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic blocks: carried parameter points are in a stretch frame where the block has them
AutoCAD evaluates actions from the dynamic block itself, so a parameter point
another action has moved out of a stretch frame still follows it. Testing the
current position instead changed a stretched label's width when its
visibility changed (Distance2 183.75 became 184.45; AutoCAD keeps 183.75).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Dynamic blocks: read parameters and actions from AutoCAD files
A dynamic block's evaluation graph (kept as foreign data since #528) is read
into a typed model, `cadcraft_doc::dynblock`, without changing the kept
data: parameters (linear with value sets, point, visibility states,
lookup, base point; polar, XY, rotation, alignment and flip by geometry)
and actions (stretch with its frame and moved vertices, lookup tables;
move, scale, rotate, flip, array, polar stretch by kind), each with its
graph id and the parameters it follows.
- `blocks.dynamic {name}` returns the model as JSON (handles as hex);
`blocks.list` marks dynamic blocks.
- Counts and values come from the file: capped by the groups present,
non-finite numbers and missing members skipped.
- Tests: a synthetic DOOR block (visibility, linear list, stretch, lookup),
its survival through a save, damaged data, and the engine commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: their values and custom properties
A dynamic block reference's extension dictionary says which dynamic block it
shows (AcDbBlockRepresentation ▸ AcDbRepData) and the values it was given
(AppDataCache ▸ ACAD_ENHANCEDBLOCKDATA, one XRECORD per parameter graph id).
`dynblock::reference` reads them; a reference to the dynamic block itself
has the block's values.
- `dynblock::custom_properties`: the Properties palette's Custom section, in
parameter order, only parameters shown in Properties: visibility state,
lookup value worked out from the lookup tables (their "no match" name, e.g.
Custom, when the inputs match no row), distances and point positions in
drawing units (block units × the reference's scale), with the choices of
each (states, lookup values, a distance's list).
- Properties: a dynamic block reference shows its dynamic block's name
instead of its anonymous block's, and a read-only Custom section.
- `blocks.reference {handle}` returns the definition, values and properties.
- Tests: synthetic references (own values, an anonymous block scaled 2, a
width no lookup row has), survival through a save, the engine command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: change the visibility state
Choosing a visibility state (or a lookup value whose tables set only
visibility states) in Properties ▸ Custom, or `blocks.reference.set
{handle, name, value}`, changes a dynamic block reference as AutoCAD does:
- The reference gets a new anonymous block: its current one with the
state's objects shown and the parameter's other objects hidden (matched
to the dynamic block's objects by their AcDbBlockRepETag element tags).
The old anonymous block goes when nothing else uses it.
- AutoCAD's link data is written: the new block's record carries
AcDbBlockRepBTag (the dynamic block's record), copied objects keep their
element tags, and the reference's AcDbBlockRepresentation data records the
value (an existing value record is updated; a new one copies another
reference's record for the same parameter when there is one).
- An attribute whose definition the state hides is written hidden (60).
- Changes CADCraft can't make yet (distances, positions, lookups that set
them) are refused with a message and change nothing; Properties shows
only what can change as a dropdown (`CustomProperty::editable`).
- Tests: the synthetic DOOR references (own values and an anonymous block),
survival through a save, refusals, and the engine command with undo.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* DWG: dynamic block lookup parameters keep their name and lookup action
AutoCAD writes a lookup parameter's subclass marker as
AcDbBlockLookUpParameter; the DWG bridge reads AcDbBlockLookupParameter and
matches it exactly, so the parameter's name (303) and lookup action (94)
were lost in DWG files and AutoCAD's lookups stopped working (a visibility
change no longer resized the block). The bridge DXF now uses its spelling.
Found by driving AutoCAD on CADCraft's output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Dynamic blocks: read parameters and actions from AutoCAD files
A dynamic block's evaluation graph (kept as foreign data since #528) is read
into a typed model, `cadcraft_doc::dynblock`, without changing the kept
data: parameters (linear with value sets, point, visibility states,
lookup, base point; polar, XY, rotation, alignment and flip by geometry)
and actions (stretch with its frame and moved vertices, lookup tables;
move, scale, rotate, flip, array, polar stretch by kind), each with its
graph id and the parameters it follows.
- `blocks.dynamic {name}` returns the model as JSON (handles as hex);
`blocks.list` marks dynamic blocks.
- Counts and values come from the file: capped by the groups present,
non-finite numbers and missing members skipped.
- Tests: a synthetic DOOR block (visibility, linear list, stretch, lookup),
its survival through a save, damaged data, and the engine commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic block references: their values and custom properties
A dynamic block reference's extension dictionary says which dynamic block it
shows (AcDbBlockRepresentation ▸ AcDbRepData) and the values it was given
(AppDataCache ▸ ACAD_ENHANCEDBLOCKDATA, one XRECORD per parameter graph id).
`dynblock::reference` reads them; a reference to the dynamic block itself
has the block's values.
- `dynblock::custom_properties`: the Properties palette's Custom section, in
parameter order, only parameters shown in Properties: visibility state,
lookup value worked out from the lookup tables (their "no match" name, e.g.
Custom, when the inputs match no row), distances and point positions in
drawing units (block units × the reference's scale), with the choices of
each (states, lookup values, a distance's list).
- Properties: a dynamic block reference shows its dynamic block's name
instead of its anonymous block's, and a read-only Custom section.
- `blocks.reference {handle}` returns the definition, values and properties.
- Tests: synthetic references (own values, an anonymous block scaled 2, a
width no lookup row has), survival through a save, the engine command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* DWG: dynamic block lookup parameters keep their name and lookup action
AutoCAD writes a lookup parameter's subclass marker as
AcDbBlockLookUpParameter; the DWG bridge reads AcDbBlockLookupParameter and
matches it exactly, so the parameter's name (303) and lookup action (94)
were lost in DWG files and AutoCAD's lookups stopped working (a visibility
change no longer resized the block). The bridge DXF now uses its spelling.
Found by driving AutoCAD on CADCraft's output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
* Dynamic blocks: read parameters and actions from AutoCAD files
A dynamic block's evaluation graph (kept as foreign data since #528) is read
into a typed model, `cadcraft_doc::dynblock`, without changing the kept
data: parameters (linear with value sets, point, visibility states,
lookup, base point; polar, XY, rotation, alignment and flip by geometry)
and actions (stretch with its frame and moved vertices, lookup tables;
move, scale, rotate, flip, array, polar stretch by kind), each with its
graph id and the parameters it follows.
- `blocks.dynamic {name}` returns the model as JSON (handles as hex);
`blocks.list` marks dynamic blocks.
- Counts and values come from the file: capped by the groups present,
non-finite numbers and missing members skipped.
- Tests: a synthetic DOOR block (visibility, linear list, stretch, lookup),
its survival through a save, damaged data, and the engine commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* DWG: dynamic block lookup parameters keep their name and lookup action
AutoCAD writes a lookup parameter's subclass marker as
AcDbBlockLookUpParameter; the DWG bridge reads AcDbBlockLookupParameter and
matches it exactly, so the parameter's name (303) and lookup action (94)
were lost in DWG files and AutoCAD's lookups stopped working (a visibility
change no longer resized the block). The bridge DXF now uses its spelling.
Found by driving AutoCAD on CADCraft's output.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dynamic blocks: a work budget on the record cursor, so counts promising missing groups can't make nested loops rescan a hostile record (with regression test)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
AutoCAD stores a TrueType text style's family (e.g. "GOST type A") in the style's ACAD xdata
and leaves the font file name empty. Styles without a file now take that family.
Family-name lookups also look in files whose name starts with the family's first word, so
"GOST type A" finds GOST.TTF (the stem shares only 4 characters with the family name).
Co-authored-by: simanov <asimfali@mail.ru>
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
A colour or freeze set in the host on an xref's layers (xref|layer) was lost on save:
the saved view dropped every xref-dependent symbol, layers included, and the DWG save goes
through the same DXF tags. The reader already keeps such layers when the xref loads.
The xref's layers are now written as xref-dependent LAYER records (DXF Reference, LAYER
group 70: 16 externally dependent, 32 resolved), as AutoCAD does with VISRETAIN = 1, with
the xref linetypes they use (same flags): without them a DWG falls back to Continuous.
Co-authored-by: Brandon Thomas <echelon@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A hatch inside a block was written with no source objects (the writer looked
for them in model and paper space only), and no boundary object carried the
hatch as a persistent reactor. AutoCAD keeps the two linked both ways; without
it a stretched dynamic block in AutoCAD moved the outline but not the fill.
Co-authored-by: Cody Vogt <18035288+codyvogt@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
An R2018+ MTEXT can carry an embedded object (group 101) in which 10 is the
X-axis direction and 11 the insertion point. AutoCAD writes one for MTEXT with
column settings, and so does the DWG bridge. The reader took the first group 11
anywhere in the entity as the direction, so such text turned towards its own
insertion point. Read 11/21 and 50 from the MTEXT's own groups only.
Another program's file can name a $HANDSEED below handles it uses (a DWG
read through the bridge did: its seed was under the handles of its
dimension blocks). The faces a polyface mesh becomes were numbered from the
seed while reading, so they could take handles of records further on in
other lists (another block); within one list duplicates were already
renumbered. A DWG keeps one object per handle, so saving one lost the
duplicates: 15 faces of a block's mesh in a permit set.
Before entities are read, every handle a file uses is now reserved. A file
CADCraft wrote names its own next handle (#495), above which its rebuilt
records are numbered, so it is left to that and resaves stay identical.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Saving regenerated every dimension's anonymous block, even dimensions read
from another program's file and never touched: the definition points went
and other programs then showed CADCraft's drawing of each dimension (a
dimension line split around its text came back whole, for instance).
A dimension still linked to the block it was read with hasn't changed
since: every edit drops the link, and the screen draws that block while it
is there. Its block is now written as read, under its name and handles;
edited and new dimensions are generated as before.
On a 1,013-dimension permit set saved DWG -> CADCraft -> DWG, every
dimension's block now matches the original (before: none).
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
From AutoCAD 2013 on, a 3DSOLID, REGION or BODY doesn't carry its ACIS
geometry: the binary SAB lives in the file's data store section (ACDSDATA),
one ACDSRECORD per entity bound by a 320 handle. CADCraft kept those
entities (as unknown entities, with their handles) but dropped the section,
so a drawing saved as DWG or DXF had empty solids, and saving reported them
as not saved.
- doc: Foreign::data_store keeps the section's groups as read;
data_store_entities() lists the entities it has records for.
- io: the reader keeps the section; the writer puts it back for files of
2013 and later (and in the DXF the DWG bridge converts, which acadrust
reads into the DWG), without the records of entities no longer written.
Nothing is written for older files or when no record's entity remains.
- engine: not_saved_as(d, version): from 2013 a solid, region or body with a
data store record isn't reported; saves and document.bytes pass the version
being written.
On a 39,600-object permit set with 625 3D solids and 2 regions, DWG ->
CADCraft -> DWG now keeps all 627 bodies with byte-identical SAB (before:
none), and the save no longer reports them.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The Model layout was written with the default page setup, whose "layout"
plot area is plot type 5, "Layout information" (DXF Reference, PLOTSETTINGS
group 74). That means nothing for model space: opened in AutoCAD 2027, a
drawing saved by CADCraft had a blank "What to plot", no preview and no scale
in the Plot dialog for Model. Model space now gets what PLOT does for it: the
drawing extents scaled to fit (74 = 1, 75 = 0). DWG saves go through the same
writer; the reader already ignores the Model layout's plot settings.
Co-authored-by: EP995LAB <293597958+EP995LAB@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
