There was no OOPS. It now brings back what the last ERASE removed (the
Delete key too), or BLOCK deleting the objects it makes a block of, as
AutoCAD 2024 does (accoreconsole, the drawing's entnext order read
back):
- Each object keeps its handle and goes back directly above the object
that was under it, or under the one that was above it when that is
gone. An erase records both neighbours (EntityStore::neighbours).
- Only the last erase counts; entdel doesn't. OOPS says nothing and is
one undo step.
- An object stays out when it is already in the drawing, when an undo
took the drawing back to before it was made, when its layer, block or
layout is gone, and, during REFEDIT, when it isn't in the working set.
REFCLOSE forgets the working copies; the Block Editor has an OOPS of
its own.
- The command's label is in the 17 interface catalogs.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Brandon Thomas <echelon@gmail.com>
Inside a routine, commands recorded no undo step (the routine becomes
one when it ends), so U inside a routine took back the step from before
the routine: after drawing a line D, ERASE B then U in one routine
brought B back and removed D.
As AutoCAD 2024 does (accoreconsole, the drawing read back after one
routine), U inside a routine now takes back the routine's last command,
with what the routine did after it (entdel, entmake); U again, UNDO n
and REDO go on through its commands. With none left, U takes back the
drawing's step before the routine, as before, and the routine's step
then starts from there. Once the routine ends it is still one undo step.
The routine's steps live in the session's LISP state (RoutineSteps), not
in the drawing's undo stack, so a long routine doesn't push the drawing's
earlier steps out. A command inside the routine ends what REDO could
bring back; UNDO Control One and None apply. DocState::swap_in is the
one restore step undo, redo and the routine share.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* SAVEAS portableFonts: Windows fonts for Linux text style fonts
A text style using a Linux TrueType font (Liberation, DejaVu, Open Sans)
shows in AutoCAD on Windows with a substitute it picks. A save now names
those styles on the command line (and as `nonPortableFonts` in the
result), and SAVEAS {"portableFonts": true} writes the Windows equivalent
in the file (Liberation -> Arial, Times New Roman, Courier New; DejaVu
Sans -> Verdana; Open Sans -> Arial) while the drawing keeps its own
fonts. Narrow and condensed families have no Windows stand-in (Arial
Narrow comes with Office) and are kept and named. QSAVE takes no SAVEAS
options.
Tests: stand_in_tests in cmd/file.rs, tests/save_portable_fonts.rs.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Portable fonts kept in the file, applied by the writer
Reworked after review. SAVEAS `portableFonts` writes a copy of the drawing
with `Drawing::portable_fonts` set, and the DXF/DWG writer turns each
style's Linux font into its Windows font, keeping the style's own font in
the CADCraft FONT xdata already used for the built-in font. Reading the
file gives the Linux fonts back (unless the font was changed since, in
AutoCAD); the drawing itself is never changed.
It applies to that save: a later QSAVE writes the drawing's fonts and
says so, naming the styles and SAVEAS portableFonts. The family table
moves to `cadcraft_fonts::windows`, used by the writer and the note.
Styles from an xref aren't saved and aren't named. The parity docs are
left to the maintainers (CLAUDE.md).
Tests: crates/io/tests/it/portable_fonts.rs (DXF, DWG, a font changed in
AutoCAD), crates/engine/tests/save_portable_fonts.rs, windows.rs tests.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Portable fonts: match the Windows font by file name
A STYLE whose Windows font carries a path (C:\Windows\Fonts\…) still
gets its own font back.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Portable fonts: say the font list again only when it changes
A save still returns nonPortableFonts, but the command line note isn't
repeated on every QSAVE of the same drawing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
